How to Read a Fiberglass Mesh Datasheet: Tensile, Coating and Mesh Count Without the Traps

How to Read a Fiberglass Mesh Datasheet: Tensile, Coating and Mesh Count Without the Traps

Two fiberglass mesh datasheets land on your desk for the same 160 g/m² reinforcement job. The numbers look almost interchangeable: both quote tensile strength in the 1,400–1,800 range, both say 5×5 mesh, both mention an alkali-resistant coating. Then the first profile goes on the wall and one mesh behaves nothing like the other. Nothing on either sheet was technically false — the two documents were simply written on different conventions, and nobody asked.

That outcome is common enough that it deserves its own skill: reading a mesh datasheet not as a list of parameters but as a set of claims, each with a hidden "measured how?" attached. This article walks the datasheet field by field, flags the three places where the same number can mean different things, and ends with the exact clarifying questions that get two supplier quotes onto one comparable basis — before you order, not after.

1

A datasheet is a claims document

A typical fiberglass mesh datasheet carries roughly a dozen fields: product code, glass type (C-glass or E-glass), weave (leno is the construction standard), mesh count or mesh size, weight per unit area, tensile strength in the warp and weft directions, sometimes elongation, coating type and content, alkali-resistance retention, roll width and length, and a handling grade such as soft, standard or hard.

Most of these fields are unambiguous — a roll width is a roll width. The trouble concentrates in three of them: tensile strength, mesh count and coating content. Each can be expressed on more than one basis, and suppliers in different markets genuinely use different ones.

A quick note on what this article is not: it is not a selection guide. Choosing a weight class or a mesh size for a given system — EIFS, stucco, waterproofing, stone backing — is its own topic and is covered in our article on choosing weight and mesh size. Here we stay inside the document itself.

2

Weight: the number everyone trusts first

Finished weight in grams per square meter is the field buyers lead with, and rightly so — it correlates with strength and with price. But two questions sit underneath it.

  • ● Finished vs. Bare: Is the figure the finished laminated weight (glass plus coating) or the bare woven fabric before coating? Coating adds roughly a tenth to a fifth of the total weight.
  • ● Tolerance: Many published tables say "approx." An approximated weight with no stated tolerance is not a specification; it is a description.

3

Tensile strength: the field with the widest trap

Tensile strength is the headline structural number, and it is also where datasheets diverge most. The value is measured by pulling a strip of mesh and recording the peak load, and everything hinges on how wide that strip is.

The Strip Width Trap

European-style datasheets report N/50mm. Others might use N/20cm. A strip four times wider carries more yarns, making the figure naturally larger for the same fabric.

Warp vs. Weft

Warp and weft are separate claims. Datasheets that print a single tensile number are averaging away information you need.

4

Mesh count: the unit decides what the number means

Mesh count looks like the simplest field, but it has a quiet trap involving two live conventions:

  • Ends per 25 mm: A "5" means five yarn ends per 25 mm (5 mm pitch).
  • Openings per inch: 5 openings per inch works out to a pitch of about 5.08 mm.

At "4x4", the difference becomes critical: four per inch is a pitch of 6.35 mm, roughly 60% larger than a 4 mm mesh.

5

Coating Content & Alkali Retention

The polymer coating makes glass mesh survivable in cement. However, a percentage needs a denominator. "18% of what?" (Finished weight vs. Bare glass weight).

For Alkali Retention, look at the conditions row: what solution, what concentration, and how many days. A 70% retention in one solution is not comparable to 90% in a milder one.

The Field-by-Field Checklist

Field What it tells you Common trap
Weight (g/m²) Glass + coating mass per area Finished vs bare-fabric basis; "approx." with no tolerance band
Tensile strength Peak load per strip width Strip width basis (N/50mm vs N/20cm); single number hiding spread
Mesh count / size Yarn density and grid pitch Per-25mm vs per-inch basis; count is not actual aperture
Coating content Polymer share protecting glass Percentage with no denominator; minimum vs typical
Alkali retention Strength kept after aging Percentage without conditions row (solution, days)

Getting Two Quotes Onto One Basis

Comparison point Supplier A Supplier B Action to make them comparable
Tensile, warp/weft "1450 / 1600, strip width 20 cm" "≥1800 / ≥1600 N/50mm" Restate strip width; compare only on matched width
Mesh count "5×5, count per 25 mm" "5×5 holes/inch" Confirm both pitches in mm
Coating content ">18%" "10–20% typical" Ask both: % of what, minimum or typical

Six clarifying questions for your next mesh RFQ

  1. "What strip width is your tensile strength measured on?"— the single question that makes strength numbers comparable at all.
  2. "Please list warp and weft tensile separately." — a single number is an average of two different claims.
  3. "Is your mesh count per 25 mm or per inch, and what is the actual opening in mm?" — resolves the 4×4 ambiguity and the aperture question in one line.
  4. "Coating content: percent of what basis, and is it a minimum or a typical value?" — turns a naked percentage into a specification.
  5. "What are the aging test conditions behind your retention figure — solution, concentration, duration — and can you send the before/after tensile report?"
  6. "What is the tolerance on finished weight, and on which basis is it measured?" — makes incoming inspection possible.

The bottom line

A fiberglass mesh datasheet is a claims document, and every number in it is only as comparable as the convention underneath it. Strip width, counting basis and percentage denominators are invisible until you ask.


Post time: Nov-17-2026